Not enough
Art.: RPS8747
Enough
Art.: PSD18305
ETHM-A is a universal monitoring module that allows you to send information over an Ethernet network The module is used in many existing and newly manufactured devices to monitor devices and send information about system events or collected data
For monitoring and reporting, ETHM-A uses several types of protocols and transmission formats that allow not only to work in local networks, but also to connect the module to the Internet, thanks to which users can access the received information using the module from any place with access to the Internet network
For monitoring and reporting, ETHM-A uses several types of protocols and transmission formats that allow not only to work in local networks, but also to connect the module to the Internet, thanks to which users can access the received information using the module from any place with access to the Internet network
Enough
Art.: RPS16202
Enough
Art.: RPS17983
Due to its reliability and high transmission quality, the 4-port desktop switch PoE PFS3006-4GT-60-V2 10/100/1000 Mb/s is an excellent solution for expanding a home or office network. Four of the ports support Power over Ethernet (PoE) functionality
Enough
Art.: RPS17623
Due to its reliability and high transmission quality, the 4-port desktop switch PoE PFS3006-4ET-60-V2 10/100 Mb/s is an excellent solution for expanding a home or office network. Four of the ports support Power over Ethernet (PoE) functionality
Enough
Art.: RPS12545
Enough
Art.: RPS13840
Not enough
Art.: RPS16214
Enough
Art.: RPS12660
Enough
Art.: RPS16444
Not enough
Art.: RPS12556
Enough
Art.: RPS21366
Not enough
Art.: RPS17769
The controller DS-K1T804BMF can work in automatic or network mode The device provides one-way or two-way transition control.
Enough
Art.: PSD13899
PFM800B-4K is intended for sending a video signal via a computer cable The device adapts the 75Ω impedance of the coaxial cable to the impedance of the symmetrical cable, ensuring video signal transmission at a distance of up to 400m (category 5 computer twisted pair) and eliminating asymmetric interference
It is necessary to pay attention to the correct connection of the (+) and (-) terminals Reverse connection causes video distortion
It is necessary to pay attention to the correct connection of the (+) and (-) terminals Reverse connection causes video distortion
Enough
Art.: RPS7604
The buffer power supply is designed to power alarm control panels, sensors, code locks, cameras, manipulators, telephone locks and other devices included in the alarm system. APS-412 has a special connector, thanks to which cooperation with Satel company equipment takes place
Enough
Art.: RPS18836
Enough
Art.: RPS20849
Enough
Art.: RPS18832
Enough
Art.: PSD18303
The ARU-200 module is used for receiving and transmitting transmissions from wireless devices ABAX 2 The ARU-200 also allows you to increase the radio range of the ABAX 2 system
The device has a buffer power supply and a built-in battery with a capacity of 1.8Ah
The device has a buffer power supply and a built-in battery with a capacity of 1.8Ah
Enough
Art.: RPS5375
The single-phase protection transformer with integrated protection against overheating and short circuit is designed and manufactured according to the standard EN61558-2-6
The power supply is intended for use in installations where the CE directive requires the use of a protective transformer The windings are separated and covered with polyurethane mass and housed in a self-extinguishing housing
Attention! If the power supply is intended for continuous operation (24H), its nominal current must not exceed 80% of the maximum current It is necessary to pay special attention to the proper cooling of the power supply during operation!
The power supply is intended for use in installations where the CE directive requires the use of a protective transformer The windings are separated and covered with polyurethane mass and housed in a self-extinguishing housing
Attention! If the power supply is intended for continuous operation (24H), its nominal current must not exceed 80% of the maximum current It is necessary to pay special attention to the proper cooling of the power supply during operation!
